EventsThe 10th International Electronic Conference on Water Sciences
Published
This submission belongs to the session S8. Wastewater Treatment and Reuse of the event The 10th International Electronic Conference on Water Sciences
Published date
19 Nov, 2026
Academic Editor
author-avatarChristos S. Akratos
Contribution&Funding
Conceptualization,
[Rodolfo Antonio Castro]
Methodology,
[Rodolfo Antonio Castro]
Software,
[Rodolfo Antonio Castro]
Validation,
[Rodolfo Antonio Castro]
Formal analysis,
[Rodolfo Antonio Castro]
Investigation,
[Rodolfo Antonio Castro]
Resources,
[Rodolfo Antonio Castro] ; [Veera Gnaneswar Gude]
Data curation,
[Rodolfo Antonio Castro]
Writing - original draft,
[Rodolfo Antonio Castro]
Writing - review,
[editing] ; [Rodolfo Antonio Castro]
Visualization,
[Rodolfo Antonio Castro]
Supervision,
[Rodolfo Antonio Castro] ; [Veera Gnaneswar Gude]
Project administration,
[Rodolfo Antonio Castro] ; [Veera Gnaneswar Gude]
Funding acquisition,
[Rodolfo Antonio Castro] ; [Veera Gnaneswar Gude]
Funding: USDA
Citation
Rodolfo Antonio Castro, Veera Gnaneswar Gude, Current Collector Free Membrane Capacitive Deionization (MCDI): 3D-Printed PETG Reactors with Self-Conducting PAN Carbon Felt Electrodes for Desalination, in Proceedings of The 10th International Electronic Conference on Water Sciences, 24 November–27 November 2026, MDPI: Basel, Switzerland
Share
Email
Facebook
Twitter
LinkedIn

Current Collector Free Membrane Capacitive Deionization (MCDI): 3D-Printed PETG Reactors with Self-Conducting PAN Carbon Felt Electrodes for Desalination

image
1. Civil and Enviromental Engineering, Purdue University Northwest, Hammond, 46320, USA
Abstract

This study presents the iterative design of a 3D-printed (using PETG via Fused Filament Fabrication), and preliminary experimental evaluation of four distinct Membrane Capacitive Deionization (MCDI) reactor configurations for desalination. Each reactor included 2 thick PAN-based carbon felt electrodes, paired with CMI-7000 cation exchange and AMI-7001 anion exchange membranes.

Four reactor configurations were evaluated across varying electrode spacings and operating voltages. Reactor 1 (50 mm spacing, ~100 mL) operated between 0.5-1.79, the reactor achieved only 0.56% salt removal, with higher voltages inducing Faradaic water splitting, evidenced by fluctuating pH values and visible gas bubble formation. Reactor 2 and 3 (7 mm spacing, ~50 mL) both operated between 0.75-1.3V, each achieving a 7.1% removal over 60 minutes. Reactor 3 added more bolt holes, inlet and outlet ports, and a rounded square chamber. Reactor 4 (20 mm, ~14 mL) operated exclusively at 1.17V. The reactor configuration achieved the highest salt removal rate at 18.5% over 60 minutes. Despite its wider spacing, this is attributed to its far lower ratio of treated volume to the electrode area, with only 14 mL processed against the same electrode footprint, the felt’s fixed adsorption capacity removed a larger fraction of dissolved salt per cycle, outweighing the higher transport resistance of the wider gap.

These findings confirm that inter-electrode spacing and applied voltage are the dominant parameters governing desalination performance, with stable operation below the 1.23V water splitting threshold essential for effective capacitive electro sorption in 3D-printed MCDI systems.

Keywords
Desalination
Membrane Capacitive Deionization
Towards Sustainable Livestock Wastewater Management: Needs Assessment on Algal-based Treatment Technology in Tanzania
Alginate Composite Beads as Adsorbents for Iron Removal from Aqueous Solutions