EventsThe 10th International Electronic Conference on Water Sciences
Published
This submission belongs to the session S8. Wastewater Treatment and Reuse of the event The 10th International Electronic Conference on Water Sciences
Published date
19 Nov, 2026
Academic Editor
author-avatarChristos S. Akratos
Contribution&Funding
Conceptualization,
[Teodora Subic] ; [Dragana Lukić]
Methodology,
[Teodora Subic]
Validation,
[Dragana Lukić]
Formal analysis,
[Teodora Subic]
Investigation,
[Teodora Subic] ; [Dragana Lukić] ; [Vesna Vasić]
Resources,
[Dragana Lukić] ; [Vesna Vasić]
Data curation,
[Dragana Lukić] ; [Vesna Vasić]
Writing - original draft,
[Teodora Subic]
Writing - review,
[editing] ; [Dragana Lukić] ; [Vesna Vasić]
Visualization,
[Teodora Subic]
Funding: --
Citation
Teodora Subic, Dragana Lukić, Vesna Vasić, Alginate Composite Beads as Adsorbents for Iron Removal from Aqueous Solutions, in Proceedings of The 10th International Electronic Conference on Water Sciences, 24 November–27 November 2026, MDPI: Basel, Switzerland
Share
Email
Facebook
Twitter
LinkedIn

Alginate Composite Beads as Adsorbents for Iron Removal from Aqueous Solutions

image
1. Faculty of Technology Novi Sad, University of Novi Sad, Novi Sad, 21000, Serbia
Abstract

With the development of innovative approaches to water purification, alginate has been increasingly used as a matrix for composites incorporating porous materials as adsorbents for pollutant removal. This study examined the potential of alginate composite beads incorporating lignocellulosic materials for total iron removal from aqueous solutions. A 1% sodium alginate solution was used to prepare pure alginate beads (ALG), as well as composite beads with exhausted chestnut wood (ALG/ECW) and its biochar (ALG/BECW). Components were mixed in a 1:1 ratio, added dropwise into a 1% CaCl2 solution to induce cross-linking, left for 24 h, and then air-dried for a further 24 h before use in adsorption experiments. Kinetic experiments were performed at an initial iron concentration of about 1 mg/L and an adsorbent dose of 2 g/L at pH 5, while equilibrium adsorption experiments covered a wider range of initial concentrations (1-700 mg/L). Equilibrium was reached after 24 h of contact time for all tested adsorbents, with the residual iron concentration reduced to as low as 0.1 mg/L for ALG/BECW. The best results were shown by ALG/BECW beads, with a removal efficiency of 90.7%, versus 75.7% for ALG/ECW and 74.3% for ALG. Kinetic data fit both pseudo-first and pseudo-second order models well (R² = 0.92–0.997). For ALG/BECW, the pseudo-first order model showed slightly better agreement (R² = 0.997). Isotherms data confirmed the adsorption capacity of ALG/BECW (qe = 34.6 mg/g), consistent with the maximum capacity predicted by the Langmuir model (qm=35.1 mg/g) provided the best fit (R² > 0.9935). Based on the obtained results, the immobilization of lignocellulosic materials in an alginate matrix represents a potential strategy for valorization of this type of waste. Further research will focus on optimizing the adsorption process and testing the performance in real water samples.

Keywords
Alginate composite beads,
Biochar
Iron removal
Current Collector Free Membrane Capacitive Deionization (MCDI): 3D-Printed PETG Reactors with Self-Conducting PAN Carbon Felt Electrodes for Desalination
VIR-CDI: Novel Voltage-Incremented Ramping Capacitive Deionization for Energy Efficient, Scalable, and Selective Physicochemical Nitrate Removal from Water