EventsThe 3rd International Online Conference on Biomimetics
Published
This submission belongs to the session S4. Bioinspired Sensorics, Information Processing and Control of the event The 3rd International Online Conference on Biomimetics
Published date
19 Nov, 2026
Academic Editor
author-avatarAndrew Adamatzky
Contribution&Funding
Conceptualization,
[Muhammad Usman Usman Yousaf]
Methodology,
[Muhammad Usman Usman Yousaf]
Software,
[Muhammad Usman Usman Yousaf]
Validation,
[Muhammad Usman Usman Yousaf]
Investigation,
[Muhammad Usman Usman Yousaf]
Resources,
[Muhammad Usman Usman Yousaf]
Data curation,
[Muhammad Usman Usman Yousaf]
Writing - original draft,
[Muhammad Usman Usman Yousaf]
Writing - review,
[editing] ; [Muhammad Usman Usman Yousaf]
Visualization,
[Muhammad Usman Usman Yousaf]
Supervision,
[Rimvydas Gaidys]
Project administration,
[Rimvydas Gaidys]
Funding acquisition,
[Rimvydas Gaidys]
Funding: This research was funded by the Research Council of Lithuania (LMTLT), agreement No. S-MIP-24-46, “Intelligent micro sensor array for physical environmental monitoring based on the mechanisms of insect mechanoreceptors and electrogenic cells in jellyfish.
Citation
Muhammad Usman Usman Yousaf, Rimvydas Gaidys, Influence of Membrane-Socket Stiffness on Directional Load Transfer in a Reconstructed Insect Mechanoreceptor, in Proceedings of The 3rd International Online Conference on Biomimetics, 24 November–26 November 2026, MDPI: Basel, Switzerland
Share
Email
Facebook
Twitter
LinkedIn

Influence of Membrane-Socket Stiffness on Directional Load Transfer in a Reconstructed Insect Mechanoreceptor

1. Department of Mechanical Engineering , Kaunas University of Technology , Kaunas, 51392, Lithuania
Abstract

Introduction

Insect hair mechanoreceptors transfer tip forces through a shaft to its enlarged base and surrounding socket. We examined whether support stiffness could change displacement amplitude while preserving the contrast between transverse and longitudinal responses. The aim was to explore a possible design principle for artificial hair sensors.

Methods

We built a COMSOL model from a published FIB-SEM reconstruction of a Nilaparvata lugens trichoid sensillum. The model contained hair, membrane/socket and dendrite domains. The hair retained its irregular basal enlargement, referred to as the basal knob. The linear static analysis used bonded interfaces and fixed outer membrane/socket surfaces. Young’s moduli were 3 × 10⁷ Pa for the hair and 10² Pa for the dendrite. The membrane/socket modulus was set to 10², 10³ or 10⁴ Pa, with 10³ Pa as the baseline. These were effective modelling inputs, not measured tissue properties. Poisson’s ratios were 0.35, 0.40 and 0.42 for the hair, membrane/socket and dendrite, respectively. Separate nominal tip loads of 1 mN were applied along transverse X and Y and longitudinal Z. Maximum absolute displacement components were extracted from the corresponding XZ, YZ and XY sections through the dendrite attachment reference. X/Z and Y/Z denote ratios of these sectional outputs. Geometry and constraints remained unchanged.

Results

At the 10³ Pa baseline, displacement differences between the 72,827-element and 162,576-element meshes were 4.68%, 3.60% and 3.63% for X, Y and Z loading, using the finer mesh as the reference. All differences were below the adopted 5% criterion, so the 72,827-element mesh was retained. Increasing the membrane/socket modulus from 10² to 10⁴ Pa reduced displacement amplitudes by approximately a factor of 100. X/Z changed from 14.28 to 14.24 and Y/Z from 14.69 to 14.62. We interpret the directional contrast in relation to the shaft’s lever arm and the basal knob within the socket. Transverse and longitudinal loads engage different combinations of bending, basal rotation and axial deformation.

Conclusions

For this geometry and mounting arrangement, support stiffness mainly changed displacement amplitude. This suggests that support compliance could help tune motion in an artificial hair sensor while preserving its directional contrast. The knob’s separate contribution requires a study in which its geometry is varied. The results describe mechanical behaviour under nominal loading and do not establish physiological sensitivity or complete sensor performance.

Acknowledgements

This research has received funding from the Research Council of Lithuania (LMTLT), agreement No S-MIP-24-46

Keywords
insect mechanoreceptor; bio-inspired sensing; directional load transfer; socket stiffness; finite-element analysis
Pharmacokinetic studies of orally administered drugs using biomimetic liquid chromatography and computational descriptors
Sprinting towards Biology: Prototyping and Model-Making in Short-Term Bio-Informed Design Sprints