EventsThe 3rd International Online Conference on Biomimetics
Published
This submission belongs to the session S1. Biomimetic Design, Constructions and Devices of the event The 3rd International Online Conference on Biomimetics
Published date
19 Nov, 2026
Academic Editor
author-avatarVictor Erokhin
Contribution&Funding
Conceptualization,
[Yi Zhao]
Methodology,
[Yi Zhao]
Formal analysis,
[Hanyang Huang]
Investigation,
[Hanyang Huang] ; [Yi Zhao]
Data curation,
[Yi Zhao]
Writing - original draft,
[Hanyang Huang] ; [Yi Zhao]
Writing - review,
[editing] ; [Yi Zhao]
Supervision,
[Yi Zhao]
Project administration,
[Yi Zhao]
Funding acquisition,
[Yi Zhao]
Funding: National Science Foundation (1509727) and Pelotonia Fellowship support
Citation
Hanyang Huang, Yi Zhao, Planar-Sensor Biomimetic Compound-Eye Optofluidic Device for Wide-Angle Imaging and Position Estimation, in Proceedings of The 3rd International Online Conference on Biomimetics, 24 November–26 November 2026, MDPI: Basel, Switzerland
Share
Email
Facebook
Twitter
LinkedIn

Planar-Sensor Biomimetic Compound-Eye Optofluidic Device for Wide-Angle Imaging and Position Estimation

Hanyang Huang 1
1. Department of Biomedical Engineering, The Ohio State University, Columbus, 43210, USA
Abstract

Wide-angle artificial vision usually follows one of two routes: a hemispherical compound-eye geometry that captures a broad field but complicates detector alignment, or a planar lens/aperture geometry that is easier to integrate with conventional sensors but has limited angular coverage. Biology suggests a way to separate these constraints. Xenos peckii-like eyes show how a planar lens/aperture architecture can sample images compactly, while mammalian eyes show how tunable focusing can provide distance selectivity. The objective of this work is to combine these functions in a planar-sensor optofluidic device that performs both wide-angle imaging and position estimation.

The design decouples angular steering from focusing. A pressure-deformable polydimethylsiloxane top membrane and refractive index-matched fluid form an adaptive prism that redirects oblique rays toward a planar image sensor. Below this prism, a 2 x 2 array of elastomer-liquid lenslets and a polymer-dispersed liquid-crystal aperture layer provide selectable imaging channels and tunable focus. Thus, top-membrane pressure controls viewing direction and field of view, whereas lenslet pressure controls focus and contributes depth information. The device was evaluated through optomechanical simulation, focal-length measurement, field-of-view characterization, distortion testing, panoramic imaging, and chessboard-based position estimation.

The lenslet focal length was tunable from 107.45 mm at 20 mbar to 8.01 mm at 400 mbar. With coordinated top-membrane and lenslet actuation, the device expanded the initial 82 deg field of view to approximately 130 deg while using a planar 1-inch CMOS sensor. A stitched dot-array image showed substantially lower peripheral distortion than a fisheye-lens comparison, with the device reaching a maximum distortion of about 16%. Wide-angle imaging of a 340 mm target and pressure-based localization of chess pieces further demonstrated adaptive imaging and position estimation across extended viewing angles.

This device demonstrates a biomimetic strategy that differs from dome-mounted adaptive lens arrays: the lenslets and detector remain planar, while a separate fluidic prism supplies angular steering and the lenslets supply accommodation-like focusing. This separation of biological functions enables wide field of view, reduced distortion, adaptive focusing, and object position estimation without a curved photodetector. The approach may benefit robotic vision, surveillance, photography, and laparoendoscopic imaging.

Keywords
biomimetic vision; bioinspired compound eye; optofluidic lens; planar image sensor; adaptive prism; wide-angle imaging; tunable focusing; position estimation
Dome-Reconfigurable Biomimetic Optofluidic Lens Array for Wide-Angle Vision and Adaptive Focus
Development of a Sensorized Soft Finger with Integrated Wiring and Its Application to a Robotic Hand